Asus RS720-E7-RS24-EG User Manual Download Page 44

Page: 44 / 202

Chapter 2: Hardware setup

2-22

2.7

Cable connections

•

The bundled system cables are pre-connected before shipment. You do not need to

disconnect these cables unless you will remove pre-installed components to install

additional devices.

•

Refer to Chapter 4 for detailed information on the connectors.

Standard cables connected to the motherboard

24-pin ATX power connector (from power supply to motherboard)

8-pin 12V power connector (from power supply to motherboard)

System and CPU fan connectors (from system fan to motherboard)

System auxiliary panel connector (from motherboard to front I/O board)

System panel connector (from motherboard to front I/O board)

SATA conectors (system default; from motherboard to SSD backplane)

USB connector (from motherboard to front I/O board)

SAS connectors (from motherboard to SATA/SAS backplane)

Summary of Contents for RS720-E7-RS24-EG











































































































































































































Search results

Summary of Contents for RS720-E7-RS24-EG

Reviews:

Related manuals for RS720-E7-RS24-EG

Brands by name

Popular brands

Asus RS720-E7-RS24-EG, User Manual

Search results

Summary of Contents for RS720-E7-RS24-EG

Reviews:

Related manuals for RS720-E7-RS24-EG

Brands by name

Popular brands