manualshive.com logo in svg

Asus RS720-E7-RS24-EG, User Manual

Share
Download
Asus RS720-E7-RS24-EG User Manual Download Page 11

xi

About this guide

Audience

This user guide is intended for system integrators, and experienced users with at 

least basic knowledge of configuring a server.

Contents

This guide contains the following parts:

1.  Chapter 1: Product introduction

This chapter describes the general features of the server, including sections 

on front panel and rear panel specifications.

2.  Chapter 2: Hardware setup

This chapter lists the hardware setup procedures that you have to perform 

when installing or removing system components.

3.  Chapter 3: Installation options

This chapter describes how to install optional components into the barebone 

server.

4.  Chapter 4: Motherboard information

This chapter gives information about the motherboard that comes with the 

server. This chapter includes the motherboard layout, jumper settings, and 

connector locations.

5.  Chapter 5: BIOS information

This chapter tells how to change system settings through the BIOS Setup 

menus and describes the BIOS parameters.

6.  Chapter 6: RAID configuration

This chapter tells how to change system settings through the BIOS Setup 

menus. Detailed descriptions of the BIOS parameters are also provided.

7 

Chapter 7: Driver installation

This chapter provides instructions for installing the necessary drivers for 

different system components.

Summary of Contents for RS720-E7-RS24-EG











































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands