manualshive.com logo in svg

Asus RS720-E7-RS24-EG, User Manual

Share
Download
Asus RS720-E7-RS24-EG User Manual Download Page 168

7-6

Chapter 7: Driver installation

3. 

Select 

Yes

 using the <Tab> key when asked if you have the driver disk, then press 

<Enter>.

Main Menu

Do you have a driver disk?

Yes

No

4. 

Insert the Red Hat

®

 Enterprise RAID driver disk to the USB floppy disk drive, select 

OK

, 

then press <Enter>.

 

The drivers for the RAID card are installed to the system.

Insert Driver Disk

OK

Back

Red Hat

®

 Enterprise Linux OS 5.6

To install the LSI MegaRAID controller driver when installing Red Hat

®

 Enterprise OS:

1. 

Boot the system from the Red Hat

®

 OS installation CD.

2. 

At the boot:, type linux dd noprobe=ata1 noprobe=ata2..., then press <Enter>.

The number of ata varies with the hard disk drive number you have when building a RAID 

set. For example, if you want to build a RAID set with 6 hard disk drives, type command 

line: linux dd noprobe=ata1 noprobe=ata2 noprobe=ata3 noprobe=ata4 noprobe=ata5 

noprobe=ata6. 

-  To install or upgrade in graphical mode, press the <ENTER> key.

-  To install or upgrade in text mode, type: linux text <ENTER>.

-  Use the function keys listed below for more information.

[F1-Main] [F2-Options] [F3-General] [F4-Kernel] [F5-Rescue]

boot: linux dd noprobe=ata1 noprobe=ata2

Insert your driver disk into /dev/fd0 

and press “OK” to continue.

Summary of Contents for RS720-E7-RS24-EG











































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands