Asus RS720-E7-RS24-EG User Manual Download Page 16

Page: 16 / 202

Chapter 1: Product introduction

1-4

1.3

System specifications

The ASUS RS720-E7-RS24-EG is a 2U barebone server system featuring the
Z9PE-D16-10G/DUAL server board. The server supports two Intel

LGA 2011 Intel

Xeon

processor E5-2600 / E5-2600 V2 product family

plus other latest technologies through

the chipsets onboard.

(continued on the next page)

* Refer to www.asus.com for the complete list of supported memory modules.

Model Name

RS720-E7-RS24-EG

Processor Support / System

Bus

2 x Socket LGA 2011

Intel

Xeon

processor

E5-2600 / E5-2600 V2 product

family

QPI 6.4 /7.2 / 8.0 GT/s

Core Logic

Intel

C602-A

Form Factor

EEB, 12 in. x 13 in.

Memory

Total Slots

16 (4 channels per CPU, 8 DIMM per CPU)

Capacity

Maximum up to 128GB

(UDIMM)

Maximum up to 512GB (RDIMM)

Maximum up to 512GB (LRDIMM)

Memory Type

DDR3 800/1066/1333/1600 RDIMM

DDR3 1066/1333 ECC UDIMM/Non-ECC UDIMM

DDR3 1066/1333 LR-DIMM

Memory Size

2GB, 4GB, 8GB, 16GB, 32GB* (RDIMM)

2GB, 4GB, 8GB* (UDIMM)

8GB, 16GB, 32GB* (LRDIMM)

Expansion

Slots (follow

SSI Location #)

Total PCI/PCI-E

Slots

Slot Location 1

1 x PCI-E x8 (x4 Gen2 link)

Slot Location 2

1 x PCI-E x16 (x16 Gen3 link)

Slot Location 3

1 x PCI-E x8 (x8 Gen3 link)

Slot Location 4

1 x PCI-E x16 (x16 Gen3 link)

Slot Location 6

1 x PCI-E x16 (x16 Gen3 link)

Additional

Slot 1

1 x PIKE Slot for Storage expansion

Networking

LAN

2 x Intel

I210AT cont 1 Management LAN

1 x Dual port Broadcom 57840S 10GbE controller

Storage

SATA Controller

Intel

C602-A:

<AHCI>

4 SATA 3Gb/s ports; 2 SATA 6Gb/s ports

Intel

RSTe

(for Windows only)

(Support software RAID 0, 1, 10, and 5)

LSI

MegaRAID

driver (Support software RAID 0, 1,

and10) (Linux/Windows)

SAS Controller

ASUS PIKE 2108-32PD 8-port SAS 6G HW RAID card

ASUS PIKE 2208 8-port SAS 6G HW RAID card

ASUS PIKE 2308 8-port SAS 6G RAID card

Default with PIKE 2108-32PD, or PIKE 2208, or PIKE 2308.

Summary of Contents for RS720-E7-RS24-EG











































































































































































































Search results

Summary of Contents for RS720-E7-RS24-EG

Reviews:

Brands by name

Popular brands

Asus RS720-E7-RS24-EG, User Manual

Search results

Summary of Contents for RS720-E7-RS24-EG

Reviews:

Brands by name

Popular brands