manualshive.com logo in svg

ASG OM Series, Manual

Share
Download
ASG OM Series Manual Download Page 8

ASG, Division of Jergens, Inc.  

15700

 S. Waterloo Road | Cleveland, OH 44110-3898 | Phone: (888) 486-6163 | Fax: (216) 481-4519 | Email: [email protected] | Web: www.asg-jergens.com

8

Adjustments and Checks before Use (Continued)

Basic Operations

Loading the Screws

•  Turn the power switch ON and OFF so that the brush stops vertically above the 

rail.

•  Open the top cover and load screws on the left and right side of the rail evenly.
•  Do not load screws above the surface of the rail.

CAUTION: 

Screws with a diameter larger than 5mm or longer than 20mm 

under the head should not be loaded higher than the rail bottom. 

•  The type and length of screw changes the load capacity so check and adjust the 

load accordingly.

•  Do not overload the hopper with screws otherwise it may cause a malfunction or 

damage the machine.

•  This machine accepts only steel screws. Plastic or stainless screws are not 

accepted.

Turning ON the Power

•  Use only the adapter supplied with this machine to connect it to a wall outlet. 

When you turn the power on, the switch lamp lights up, the motor rotates, and 
screws are brushed onto the rail.

•  The rail vibrates to deliver screws toward the end of the rail, then the escape 

rotates to deliver screws to the pick-up location. When the screws come to the 
stopper, the LED indicator lights up and the escape stops rotating. 

•  CAUTION:

 Use only the AC adapter supplied with this machine otherwise it may 

cause damage to the machine.

!

Summary of Contents for OM Series


































Reviews:

No comments

Brands by name

Popular brands

Load more brands