ASG OM Series Manual Download Page 15

Page: 15 / 33

ASG, Division of Jergens, Inc.

15700

Maintenance

• A dirty rail may interfere with the screw transport speed. Clean the rail with a

soft, clean cloth dipped in alcohol. If cleaning is difficult, remove the rail from the
machine and clean the rail. Replace the rail if needed.

• Before removing the rail from the machine, be sure to turn off the power supply

and take the screws out of the hopper.

Part Adjustments and Replacement

• The brush and main motor are wearable parts.
• When using a different diameter of screw, the following items must be replaced:

rail, escape, and passing plate. These parts may be ordered separately. The
replacement and adjustment procedures are described on the next page.

• When replacing any parts, a fine adjustment is required. Make these fine

adjustments by following the instructions in this manual. Before replacing any
parts, be sure to remove all the screws from the hopper.

Summary of Contents for OM Series


































Search results

Summary of Contents for OM Series

Reviews:

Brands by name

Popular brands

ASG OM Series, Manual

Search results

Summary of Contents for OM Series

Reviews:

Brands by name

Popular brands