manualshive.com logo in svg

ASG OM Series, Manual

Share
Download
ASG OM Series Manual Download Page 19

ASG, Division of Jergens, Inc.  

15700

 S. Waterloo Road | Cleveland, OH 44110-3898 | Phone: (888) 486-6163 | Fax: (216) 481-4519 | Email: [email protected] | Web: www.asg-jergens.com

19

Part Adjustments and Replacement (Continued)

Replacing and Adjustment of the Escape (Continued)

4.  Adjust the escape notch position.
•  Turn the power switch ON while covering the sensor light axis with a small piece 

of paper. 

•  When the power is ON, the screw sensor LED lights up and the escape rotates 

around to the starting point.(Reference point run.) 

•  When the escape stops, loosen the attaching screws and adjust the escape 

by hand so that an escape notch and the rail groove align. Tighten the escape 
attaching screws. 

•  After adjustment, turn the power switch ON in order to make a reference point 

run and check that an escape notch and the rail groove align.

•  Next, remove the paper blocking the sensor’s optical axis and the escape will start 

rotating.

•  At each rotation stop, check that all 4 notches of the escape align with the rail.
•  After checking and adjusting each component, do an operational check with 

screws loaded.

•  If any abnormality is found, make the said adjustments once again in addition to 

the rail vibration and front/rear position adjustments.

•  When installing the cover, take care not to catch or pinch the wires.

Summary of Contents for OM Series


































Reviews:

No comments

Brands by name

Popular brands

Load more brands