manualshive.com logo in svg

ASG OM Series, Manual

Share
Download
ASG OM Series Manual Download Page 13

ASG, Division of Jergens, Inc.  

15700

 S. Waterloo Road | Cleveland, OH 44110-3898 | Phone: (888) 486-6163 | Fax: (216) 481-4519 | Email: [email protected] | Web: www.asg-jergens.com

13

Adjustments and Checks before Use (Continued)

Check and Adjust the Passing Plate 

Turn OFF the power switch before starting replacement and adjustment.

•  Check that the passing plate is adjusted to a height that permits loaded screws to 

pass just within the limit.

•  If the passing plate is too low, screws cannot pass. If the passing plate is too high, 

the screws will not be transported smoothly. 

•  If adjustment is required, loosen the passing plate screw and adjust appropriately.

Check and Adjust the Holding Plate 

•  Check that the clearance between screws in the rail and the holding plate is 

about 0-1mm.

•  If any adjustment is required, loosen the holding plate attachment screw and turn 

the holding plate adjusting screw to move the plate up or down.

•  If there is no clearance, the screw cannot pass. If the clearance is too large, screw 

may pile up or escape.  Turn the holding plate adjusting screw clockwise to move 
the plate down. Turn the holding plate adjusting screw counter-clockwise to move 
the plate up.

!

Summary of Contents for OM Series


































Reviews:

No comments

Brands by name

Popular brands

Load more brands