manualshive.com logo in svg

ASG OM Series, Manual

Share
Download
ASG OM Series Manual Download Page 14

ASG, Division of Jergens, Inc.  

15700

 S. Waterloo Road | Cleveland, OH 44110-3898 | Phone: (888) 486-6163 | Fax: (216) 481-4519 | Email: [email protected] | Web: www.asg-jergens.com

14

Adjustments and Checks before Use (Continued)

Check and Adjust the Timer

•  The screw transport feed differs depending on screw type.
•  Set the timer longer for screws with a low transport speed and shorter for screws 

with a high transport speed.

•  This machine continues its operation when no screw is found at the screw pick up 

spot. 

•  The machine continues operating with a screw at the pick up location but will 

stop after a certain time period if the screw is not picked up. This time period can 
be varied by adjusting the timer. After the screw is picked up, the machine starts 
operating again.

•  Cover one of the optical sensors to make sure it’s working.
•  Make an adjustment with the timer adjusting knob (the 3rd hole from the top) at 

the rear of the machine body (as shown in the figure on the right).

•  Turn the timer knob clockwise (as viewed from the rear side) to decrease the time 

period.  Turn the knob counter-clockwise to increase the time period.

Check and Adjust the Scraper 

•  Check that the clearance between the scraper right/left and the hopper wall right/ 

left, are around 0.4mm. 

•  When the scraper makes contact with the hopper wall, the rail vibration decreases 

and the screws are delivered slowly. When the clearance between the scraper and 
the hopper wall is too large, the screws may be caught by the scraper.

•  If any adjustment is required, loosen the scraper attaching screw and move the 

scraper plate up or down.

•  If there is any damage to the plate, contact ASG.  

Summary of Contents for OM Series


































Reviews:

No comments

Brands by name

Popular brands

Load more brands