manualshive.com logo in svg

ASG OM Series, Manual

Share
Download
ASG OM Series Manual Download Page 10

ASG, Division of Jergens, Inc.  

15700

 S. Waterloo Road | Cleveland, OH 44110-3898 | Phone: (888) 486-6163 | Fax: (216) 481-4519 | Email: [email protected] | Web: www.asg-jergens.com

10

Adjustments and Checks before Use (Continued)

Adjusting the Brush Height

Turn OFF the power switch before starting replacement and adjustment.

•  Load the screws into the screw hopper and turn ON the power switch until the 

screws are aligned in the rail. 

•  Turn power switch ON and OFF in order to set the brush to the left as shown in 

the figure on the right.

•  Move the brush by hand to check that the screws in the rail are in slight contact 

with the brush bristles. If needed, make necessary adjustments.

•  When the brush height is too high or low, this will have an adverse effect on the 

screw alignment and transport.

•  If any adjustment is necessary, loosen the brush height adjusting bolt to adjust 

the brush height.

•  If the plastic portion at the front of the brush comes into contact with the passing 

plate, loosen the brush assembly mounting screw and move the brush assembly 
back so there is no clearance.

•  Turn ON the power switch to check that the brush operation is normal.

!

Summary of Contents for OM Series


































Reviews:

No comments

Brands by name

Popular brands

Load more brands