manualshive.com logo in svg

Artistic Edge 12, User Manual, Page: 16 / 32

Share
Download
Artistic Edge 12 User Manual Download Page 16

16

6.  After the process is complete, your PC will automatically re-establish the connection to your home network, you 
can verify this by hovering your mouse pointer over the wireless icon located in the system tray                             , you 
should see the name of your home wireless network.

7.  The next time you send a file to your cutter, click File>Export> To Cutters, after a few moments your Edge cutter will 
automatically pop-up in the Select Cutter/Type window, then select your Edge cutter and click “Connect”.

8.  The cutter dialogue window will open ready for you to send your file.

Troubleshooting - Emergency reset to Access point mode.

If you cannot connect to the cutter or any miss-configuration has happened and you cannot access the cutter, you 
must reset the cutter to the default “Access point” mode and then re-connect to any wireless network in “Client mode” 
again. In order to reset the cutter, you must keep the “Wireless button” and “Right limit button” pressed together for 
3 seconds. When the “Power” button and the “Wireless button” is turned off, you may then release the button. At this 
point the “Wireless button” will start blinking until the network initialization is completed. When the blinking stops you 
are ready to connect to Edge-xx-xx-xx access point in order to use the cutter. 

Summary of Contents for Edge 12

































Reviews:

No comments