artisan TurboStacK AT-TS06F Installation Manual Download Page 48

Page: 48 / 97

TurboStack Hubs with Management

Figure 27 shows the threaded SM connectors.

Port Indicators

The port indicators on the AT-TS06F/ST, SC, SM Series repeater front
panels provide visual diagnostic and activity information for network
analysis, as shown in Figure 28.

Each fiber optic port supports the following indicator functions with one
dual-color front panel LED per port.

GREEN LINK—Steady illumination indicates that the port has a valid
link and is not partitioned.

GREEN RECEIVE—Flashing illumination indicates that the port has a
valid link, is not partitioned, and is receiving data.

Figure 27: SM Connector for

Fiber Optic Cabling

Figure 28: AT-TS06F/SC Port

Activity LEDs

Port activity LED symbols

Port activity LED

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for TurboStacK AT-TS06F


































































































Search results

Summary of Contents for TurboStacK AT-TS06F

Reviews:

Related manuals for TurboStacK AT-TS06F

Brands by name

Popular brands

artisan TurboStacK AT-TS06F, Installation Manual

Search results

Summary of Contents for TurboStacK AT-TS06F

Reviews:

Related manuals for TurboStacK AT-TS06F

Brands by name

Popular brands