artisan TurboStacK AT-TS06F Page 58 Installation Manual Download

Page: 58 / 97

TurboStack Hubs with Management

Figure 39 shows the threaded SM connectors.

Port Indicators

The port indicators and corresponding symbopls on the AT-TS12F/ST, SC,
SM Series repeater front panels provide visual diagnostic and activity
information for network analysis (see Figure 40).

Each fiber optic port supports the following indicator functions with one
dual-color front panel LED per port.

GREEN LINK—Steady illumination indicates that the port has a valid
link and is not partitioned.

GREEN RECEIVE—Flashing illumination indicates that the port has a
valid link, is not partitioned, and is receiving data.

AMBER PARTITION—Steady illumination indicates that the port has a
valid link and

partitioned.

Figure 39: SM Connector for

Fiber Optic Cabling

Figure 40: AT-TS12F Port

Activity LED
symbols

Port activity LED symbols

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for TurboStacK AT-TS06F


































































































Search results

Summary of Contents for TurboStacK AT-TS06F

Reviews:

Related manuals for TurboStacK AT-TS06F

Brands by name

Popular brands

artisan TurboStacK AT-TS06F, Installation Manual

Search results

Summary of Contents for TurboStacK AT-TS06F

Reviews:

Related manuals for TurboStacK AT-TS06F

Brands by name

Popular brands