artisan TurboStacK AT-TS06F Installation Manual Download Page 39

Page: 39 / 97

TurboStack Hubs with Management

Separate the AUI appliqué connector plate (shown in Figure 15) from
the ribbon cable (shown in Figure 16) by rotating the cable 90

and

sliding it through the slot in the connector plate.

Store the detached AUI appliqué plate, slide kit screws, washers, and
nuts in a secure container for future use.

To install a 10BASE2, 10BASE-T or fiber Optic (10BASE-FL)
appliqué

Remove the AUI appliqué (as described above).

Plug the replacement 10BASE2, 10BASE-T, or 10BASE-FL appliqué
into the AUI connector, as shown in Figure 17.

Figure 16: AUI Connector and

Ribbon Cable
Assembly

Figure 17: Appliqué

Installation

AUI

connector

Ribbon cable

without
connector plate

Replacement
cover plate

AUI connector

Replacement
appliqué

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for TurboStacK AT-TS06F


































































































Search results

Summary of Contents for TurboStacK AT-TS06F

Reviews:

Related manuals for TurboStacK AT-TS06F

Brands by name

Popular brands

artisan TurboStacK AT-TS06F, Installation Manual

Search results

Summary of Contents for TurboStacK AT-TS06F

Reviews:

Related manuals for TurboStacK AT-TS06F

Brands by name

Popular brands