Artesyn MITX-CORE-820 Installation And Use Manual Download Page 14

Page: 14 / 133

List of Figures

MITX-CORE-820 Installation and Use (6806800M10H)

Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Figure 1-2

MITX-CORE-820 Mechanical Data (Top View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Figure 1-3

MITX-CORE-820 Mechanical Data (Side View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Figure 1-4

MITX-CORE-820 Serial Number Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Figure 3-1

MITX-CORE-820 Module Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Figure 3-2

MITX-CORE-820 Module Components - Continued . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Figure 3-3

Rear I/O Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Figure 4-1

Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Figure 4-2

Platform Clocks Distribution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Figure 4-3

LVDS Inverter Connector (P8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Figure 4-4

SATA HDD Power Connector (P17) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Figure 4-5

USB Internal Header (P24, P25, P26) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Figure 4-6

DC-IN Jack Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Figure 4-7

ATX Power Supply Connector Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Figure 4-8

CPU and System Fan Headers (P2 and P23) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Figure 4-9

PS/2 Header (P5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Figure 4-10

SMBUS Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Figure 4-11

Rear Panel Audio Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Figure 4-12

Front Panel Audio Header (P9) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Figure 4-13

Front Panel Header (P1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Figure 4-14

TPM/Port80 Header (P3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Figure 5-1

Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Figure 5-2

Advanced Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Figure 5-3

Security Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

Figure 5-4

Boot Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

Figure 5-5

Exit Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

Figure 6-1

NPCE791x System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

Figure 6-2

Structure of Standard Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

Figure A-1

Battery Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

Summary of Contents for MITX-CORE-820






































































































































Search results

Summary of Contents for MITX-CORE-820

Reviews:

Artesyn MITX-CORE-820, Installation And Use Manual, Page: 14 / 133

Search results

Summary of Contents for MITX-CORE-820

Reviews: