ARM ARM9TDMI Technical Reference Manual Download | Manualshive

Page: 91 / 154

background image

Debug Support

ARM DDI0145B

Copyright © 1998, 1999 ARM Limited. All rights reserved.

5-37

This restores the PC, and restarts the program from the next instruction.

5.12.6

System speed accesses

If a system speed access is performed during debug state, the value of the PC is
increased by five addresses. Since system speed instructions access the memory system,
it is possible for aborts to take place. If an abort occurs during a system speed memory
access, the ARM9TDMI enters abort mode before returning to debug state.

This is similar to an aborted watchpoint. However, the problem is much harder to fix
because the abort was not caused by an instruction in the main program, and the PC does
not point to the instruction that caused the abort. An abort handler usually looks at the
PC to determine the instruction that caused the abort, and hence the abort address. In
this case, the value of the PC is invalid, but the debugger will know the address of the
location that was being accessed. Thus the debugger can be written to help the abort
handler fix the memory system.

5.12.7

Summary of return address calculations

The calculation of the branch return address can be summarized as:

-(4 + N +5S)

where

N

is the number of debug speed instructions executed (including the final branch),

and

S

is the number of system speed instructions executed.

«
...
89
90
91
92
93
...
»

Summary of Contents for ARM9TDMI



























































































































































Reviews:

No comments

Related manuals for ARM9TDMI

Brand: Data Translation Pages: 60

Brand: Magma Pages: 2

COMSPHERE 3800 Series

Brand: Paradyne Pages: 88

COMSPHERE 3800PLUS

Brand: Paradyne Pages: 5

Brand: NXP Semiconductors Pages: 24

Brand: Avolites Pages: 24

Brand: Z Microsystems Pages: 51

Optane Persistent Memory 200 Series

Brand: Supermicro Pages: 54

Brand: Infoblox Pages: 13

Brand: Idis Pages: 20

UniFi LED ULED-AT

Brand: Ubiquiti Pages: 16

Brand: A.E.B. Pages: 28

HiGain Line Unit HLU-388

Brand: PairGain Pages: 7

Sporlan Division SCS-PB Series

Brand: Parker Pages: 10

Brand: ADLINK Technology Pages: 34

Internet Security Appliances

Brand: SonicWALL Pages: 293

Brand: WATT & WELL Pages: 15

Brand: Fujitsu Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands