ARM ARM9TDMI Technical Reference Manual Download

Page: 143 / 154

ARM9TDMI Signal Descriptions

ARM DDI0145B

A-5

A.3

Coprocessor interface signals

For further information on the coprocessor interface refer to Chapter 4

ARM9TDMI

Coprocessor Interface

Table A-3 Coprocessor interface signals

Name

Direction

Description

CHSD[1:0]

Input

Coprocessor Handshake Decode. The handshake signals from the decode stage of the
coprocessors pipeline follower.

Note, if no coprocessor is present in the system,

CHSD[1]

should be tied HIGH, and

CHSD[0]

should be tied LOW.

CHSE[1:0]

Input

Coprocessor Handshake Execute. The handshake signals from the execute stage of the
coprocessors pipeline follower.

Note, if no coprocessor is present in the system,

CHSE[1]

should be tied HIGH, and

CHSE[0]

should be tied LOW.

LATECANCEL

Output

Coprocessor Late Cancel. If HIGH during the first memory cycle of a coprocessor
instruction’s execution, the coprocessor should cancel the instruction without having
updated its state.

PASS

Output

Coprocessor

PASS

. This signal indicates that there is a coprocessor instruction in the

execute stage of the pipeline, and it should be executed.

Summary of Contents for ARM9TDMI











































































































































Search results

Summary of Contents for ARM9TDMI

Reviews:

Related manuals for ARM9TDMI

Brands by name

Popular brands

ARM ARM9TDMI, Technical Reference Manual

Search results

Summary of Contents for ARM9TDMI

Reviews:

Related manuals for ARM9TDMI

Brands by name

Popular brands