ARM ARM7TDMI Technical Reference Manual Download Page 73

Page: 73 / 286

Memory Interface

ARM DDI 0210C

3-3

3.2

Bus interface signals

The signals in the ARM7TDMI processor bus interface can be grouped into four
categories:

•

clocking and clock control

•

address class signals

•

memory request signals

•

data timed signals.

The clocking and clock control signals are:

•

MCLK

•

nWAIT

•

ECLK

•

nRESET

The address class signals are:

•

A[31:0]

•

nRW

•

MAS[1:0]

•

nOPC

•

nTRANS

•

LOCK

•

TBIT

The memory request signals are:

•

nMREQ

•

SEQ

The data timed signals are:

•

D[31:0]

•

DIN[31:0]

•

DOUT[31:0]

•

ABORT

•

BL[3:0]

The ARM7TDMI processor uses both the rising and falling edges of

MCLK

Bus cycles can be extended using the

nWAIT

signal. This signal is described in

Stretching access times

on page 3-29. All other sections of this chapter describe a

simple system in which

nWAIT

is permanently HIGH.

Summary of Contents for ARM7TDMI





















































































































































































































































































Search results

Summary of Contents for ARM7TDMI

Reviews:

Related manuals for ARM7TDMI

Brands by name

Popular brands

ARM ARM7TDMI, Technical Reference Manual

Search results

Summary of Contents for ARM7TDMI

Reviews:

Related manuals for ARM7TDMI

Brands by name

Popular brands