ARM ARM7TDMI Technical Reference Manual Download Page 141 | Manualshive

Page: 141 / 286

background image

Debug Interface

ARM DDI 0210C

Copyright © 2001, 2004 ARM Limited. All rights reserved.

5-21

5.9

Monitor mode

The ARM7TDMI processor contains logic that enables the debugging of a system
without stopping the core entirely. This enables the continued servicing of critical
interrupt routines while the core is being interrogated by the debugger. Setting bit [4] of
the debug control register enables the monitor mode features of the ARM7TDMI
processor. When this bit is set, the EmbeddedICE-RT logic is configured so that a
breakpoint or watchpoint causes the ARM7TDMI core to enter abort mode, taking the
Prefetch or Data Abort vectors respectively. There are a number of restrictions you must
be aware of when the ARM core is configured for monitor-mode debugging:

•

Breakpoints and watchpoints cannot be data-dependent in monitor mode. No
support is provided for use of the range functionality. Breakpoints and
watchpoints can only be based on:

—

instruction or data addresses

—

external watchpoint conditioner (

EXTERN0

or

EXTERN1

)

—

User or privileged mode access (

nTRANS

)

—

read/write access for watchpoints (

nRW

)

—

access size (watchpoints

MAS[1:0]

).

•

External breakpoints or watchpoints are not supported.

•

No support is provided to mix halt mode and monitor mode functionality.

The fact that an abort has been generated by the monitor mode is recorded in the abort
status register in coprocessor 14 (see

The abort status register

on page B-56).

The monitor mode enable bit does not put the ARM7TDMI processor into debug state.
For this reason, it is necessary to change the contents of the watchpoint registers while
external memory accesses are taking place, rather than changing them when in debug
state where the core is halted.

If there is a possibility of false matches occurring during changes to the watchpoint
registers (caused by old data in some registers and new data in others) you must:

1.

Disable the watchpoint unit by setting EmbeddedICE-RT disable, bit [5] in the
debug control register.

2.

Poll the debug control register until the EmbeddedICE-RT disable bit is read back
as set.

3.

Change the other registers.

4.

Re-enable the watchpoint unit by clearing the EmbeddedICE-RT disable bit in the
debug control register.

«
...
139
140
141
142
143
...
»

Summary of Contents for ARM7TDMI































































































































































































































































































Reviews:

No comments

Related manuals for ARM7TDMI

Brand: Yaesu Pages: 2

Brand: 3Com Pages: 16

Brand: Opvimus Pages: 12

TD-3316B4-16P-A1

Brand: TVT Digital Pages: 2

NVR41-4KS2 Series

Brand: Dahua Pages: 452

BiPAC 5200S RC Series

Brand: Billion Pages: 79

COM Express conga-TC87

Brand: Congatec Pages: 114

CORE 2 DUO E4000 - 3-2008

Brand: Intel Pages: 122

Total Access 1500 Dual FXS/DPO

Brand: ADTRAN Pages: 2

N-FXE 02B Series

Brand: Lantronix Pages: 10

Brand: Cowlacious Designs Pages: 8

SPEEDTOUCH 110G

Brand: THOMSON Pages: 26

Brand: ICP DAS USA Pages: 8

2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 1 01-2011

Brand: Intel Pages: 172

Brand: SilverStone Pages: 12

EK-UNI Holder D5 V3

Brand: ekwb Pages: 2

FusionHDTV 5 GOLD

Brand: Dvico Pages: 64

Brand: EKF Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands