ARM ARM7TDMI Technical Reference Manual Download Page 123

Page: 123 / 286

Debug Interface

ARM DDI 0210C

5-3

5.1.2

Clocks

The ARM7TDMI core has two clocks:

•

MCLK

is the memory clock

•

DCLK

is an internal debug clock, generated by the test clock,

TCK

During normal operation, the core is clocked by

MCLK

and internal logic holds

DCLK

LOW.

When the ARM7TDMI processor is in halt mode, the core is clocked by

DCLK

under

control of the TAP state machine and

MCLK

can free-run. The selected clock is output

on the signal

ECLK

for use by the external system.

Note

NWAIT

must be HIGH in debug state.

In monitor mode, the core continues to be clocked by

MCLK

, and

DCLK

is not used.

Summary of Contents for ARM7TDMI





















































































































































































































































































Search results

Summary of Contents for ARM7TDMI

Reviews:

Related manuals for ARM7TDMI

Brands by name

Popular brands

ARM ARM7TDMI, Technical Reference Manual

Search results

Summary of Contents for ARM7TDMI

Reviews:

Related manuals for ARM7TDMI

Brands by name

Popular brands