manualshive.com logo in svg

ARM ARM7TDMI, Technical Reference Manual

The ARM ARM7TDMI User Manual is available for free download on our website. This comprehensive manual provides detailed instructions and guidelines on operating and optimizing your ARM7TDMI processor. Enhance your understanding of this product by downloading the user manual from manualshive.com.

Share
Download
background image

Debug Interface 

5-10

Copyright © 2001, 2004 ARM Limited. All rights reserved.

ARM DDI 0210C

instruction is a busy-waiting access to a coprocessor, the instruction terminates and 
ARM7TDMI processor enters debug state immediately. This is similar to the action of 

nIRQ

 and 

nFIQ

.

5.3.2

Action of the ARM7TDMI processor in debug state

In debug state, 

nMREQ

 and 

SEQ

 indicate internal cycles. This enables the rest of the 

memory system to ignore the core and function as normal. Because the rest of the 
system continues to operate, the ARM7TDMI processor is forced to ignore aborts and 
interrupts. 

The system must not change the following signals during debug:

BIGEND 

If 

BIGEND

 changes during debug:

•

synchronization problems are introduced

•

the programmer’s view of the processor changes without the 
knowledge of the debugger.

nRESET 

Resetting the core while debugging causes the debugger to lose 
track of the core.

When the system applies reset to the ARM7TDMI processor by 
driving 

nRESET

 LOW, the processor state changes with the 

debugger unaware that the core has reset.

When instructions are executed in halt mode, all memory interface outputs except 

nMREQ

 and 

SEQ

 change asynchronously to the memory system. For example, every 

time a new instruction is scanned into the pipeline, the address bus changes. 

The memory controller must be designed to ensure that asynchronous behavior does not 
affect the rest of the system. Although the behavior of 

nMREQ

 and 

SEQ

 is 

asynchronous, this does not affect the system because 

nMREQ

 and 

SEQ

 are forced to 

indicate internal cycles regardless of the behavior of the rest of the core. 

5.3.3

Action of the ARM7TDMI core in monitor mode

In monitor mode, the ARM7TDMI processor continues to execute instructions, and the 
memory interface behaves as normal.

Summary of Contents for ARM7TDMI































































































































































































































































































Reviews:

No comments

Related manuals for ARM7TDMI

Devolo Magic WiFi mini Ek Manual preview
Magic WiFi mini Ek
Brand: Devolo Pages: 22
u-blox ANT-B10 User Manual preview
ANT-B10
Brand: u-blox Pages: 29
Lanner electronics EM-566 Series Manual preview
EM-566 Series
Brand: Lanner electronics Pages: 59
ADC HiGain H2TU-R-402 List 7A Quick Installation preview
HiGain H2TU-R-402 List 7A
Brand: ADC Pages: 7
Renesas H8S/2633 User Manual preview
H8S/2633
Brand: Renesas Pages: 28
Z3 Technology Z3-SBE264-10 User Instructions preview
Z3-SBE264-10
Brand: Z3 Technology Pages: 67
ZALMAN CNPS11X Extreme User Manual preview
CNPS11X Extreme
Brand: ZALMAN Pages: 12
CNC4PC C52- ESS User Manual preview
C52- ESS
Brand: CNC4PC Pages: 11
Microchip Technology DM240316 Quick Start Manual preview
DM240316
Brand: Microchip Technology Pages: 9
UNICORECOMM UM620N User Manual preview
UM620N
Brand: UNICORECOMM Pages: 19
Vivotek ND8212W Hardware Installation Manual preview
ND8212W
Brand: Vivotek Pages: 46
Acces I/O products mPCIE-ADIO16-8F Series Hardware Manual preview
mPCIE-ADIO16-8F Series
Brand: Acces I/O products Pages: 13
M86 Security IR Web Filter User Manual preview
IR Web Filter
Brand: M86 Security Pages: 540
OWC ENVOY PRO MINI User Manual preview
ENVOY PRO MINI
Brand: OWC Pages: 7
Curtiss-Wright KAD/UBM/105 Quick Start Manual preview
KAD/UBM/105
Brand: Curtiss-Wright Pages: 12
Curtiss-Wright GT200 VME Hardware Reference Manual preview
GT200 VME
Brand: Curtiss-Wright Pages: 58
Lava PayLink-IP/Dial Quick Installation Manual preview
PayLink-IP/Dial
Brand: Lava Pages: 16
ACASIS M13 User Manual preview
M13
Brand: ACASIS Pages: 6

Brands by name

Popular brands

Load more brands