manualshive.com logo in svg

ARM ARM7TDMI, Technical Reference Manual

The ARM ARM7TDMI User Manual is available for free download on our website. This comprehensive manual provides detailed instructions and guidelines on operating and optimizing your ARM7TDMI processor. Enhance your understanding of this product by downloading the user manual from manualshive.com.

Share
Download
background image

Debug in Depth 

B-20

Copyright © 2001, 2004 ARM Limited. All rights reserved.

ARM DDI 0210C

•

During SHIFT-DR, a data value is shifted into the serial register. Bits 32 to 36 
specify the address of the EmbeddedICE-RT logic register to be accessed.

•

During UPDATE-DR, this register is either read or written depending on the state 
of bit [37], as follows:

Bit [37] set 

Register is written.

Bit [37] cleared 

Register is read.

Scan chain 3

Purpose 

Enables the ARM7TDMI core to control an external boundary-scan 
chain.

Length 

User defined.

Scan chain 3 control signals are provided so that an optional external boundary-scan 
chain can be controlled through the ARM7TDMI core. Typically, this is used for a scan 
chain around the pad ring of a packaged device.

The following control signals are provided which are generated only when scan chain 
3 has been selected. These outputs are inactive at all other times:

DRIVEBS 

This is used to switch the scan cells from system mode to test mode. This 
signal is asserted whenever either the INTEST, EXTEST, CLAMP, or 
CLAMPZ instruction is selected.

PCLKBS 

This is an update clock, generated in the UPDATE-DR state. Typically 
the value scanned into a chain is transferred to the cell output on the rising 
edge of this signal.

ICAPCLKBS, ECAPCLKBS 

These are capture clocks used to sample data into the scan cells during 
INTEST and EXTEST respectively. These clocks are generated in the 
CAPTURE-DR state.

SHCLKBS, SHCLK2BS 

These are non-overlapping clocks generated in the SHIFT-DR state used 
to clock the master and slave element of the scan cells respectively. When 
the state machine is not in the SHIFT-DR state, both these clocks are 
LOW.

Summary of Contents for ARM7TDMI































































































































































































































































































Reviews:

No comments

Related manuals for ARM7TDMI

Idis DR-4100P Series Installation Manual preview
DR-4100P Series
Brand: Idis Pages: 30
Ubiquiti U5-24-500W Quick Start Manual preview
U5-24-500W
Brand: Ubiquiti Pages: 23
ekwb EK-FB GA AX370 Gaming RGB Monoblock Installation Manual preview
EK-FB GA AX370 Gaming RGB Monoblock
Brand: ekwb Pages: 2
NEC P401-TMX4D User Manual preview
P401-TMX4D
Brand: NEC Pages: 2
IEI Technology PUZZLE-IN003B User Manual preview
PUZZLE-IN003B
Brand: IEI Technology Pages: 86
Dahua Technology Lite N42B1P Series Quick Start Manual preview
Lite N42B1P Series
Brand: Dahua Technology Pages: 14
Parker ACR1200 Hardware Manual preview
ACR1200
Brand: Parker Pages: 50
Navitar 1-62645 Dimensional Drawing preview
1-62645
Brand: Navitar Pages: 1
VideoWave Adam Device User Manual preview
Adam Device
Brand: VideoWave Pages: 12
PairGain T1L2PY0AA Manual preview
T1L2PY0AA
Brand: PairGain Pages: 80
ADS Technologies API-800 Installation Manual preview
API-800
Brand: ADS Technologies Pages: 21
AMD Geode LX 800 User Manual preview
Geode LX 800
Brand: AMD Pages: 27
EXAGATE SYSGuard 6001 Quick Installation Manual preview
SYSGuard 6001
Brand: EXAGATE Pages: 7
S&P Turbo-3000 Operating Instructions preview
Turbo-3000
Brand: S&P Pages: 3
ProSoft MVI46-PDPS User Manual preview
MVI46-PDPS
Brand: ProSoft Pages: 53
Cowlacious Designs ISD CAP 275 Manual preview
ISD CAP 275
Brand: Cowlacious Designs Pages: 8
Lucent Technologies CIB40 Installation Manual preview
CIB40
Brand: Lucent Technologies Pages: 7
Paradyne Hotwire 7996 User Manual preview
Hotwire 7996
Brand: Paradyne Pages: 46

Brands by name

Popular brands

Load more brands