manualshive.com logo in svg

ARM ARM7TDMI, Technical Reference Manual

The ARM ARM7TDMI User Manual is available for free download on our website. This comprehensive manual provides detailed instructions and guidelines on operating and optimizing your ARM7TDMI processor. Enhance your understanding of this product by downloading the user manual from manualshive.com.

Share
Download
background image

Differences Between Rev 3a and Rev 4 

ARM DDI 0210C

Copyright © 2001, 2004 ARM Limited. All rights reserved.

C-3

C.2

Detailed descriptions of differences between Rev 3a and Rev 4

This section describes the changes to ARM7TDMI Rev 4 in detail.

C.2.1

Improved low voltage operation

Reliable operation down to 1V is expected on most 0.18µm processes.

C.2.2

Addition of EmbeddedICE-RT logic

EmbeddedICE-RT is an enhanced implementation of the EmbeddedICE logic that was 
part of the ARM7TDMI Rev 3a. The extra feature provided by EmbeddedICE-RT is 
that upon a breakpoint or watchpoint, the core can be forced to take an exception, rather 
than simply entering debug state. Because the core does not enter debug state, it can 
continue to service hardware interrupt requests as normal.

This feature is extremely useful where the core forms part of the feedback loop of a 
mechanical system, where stopping the core could potentially lead to system failure.

The addition of two extra bits to the debug control register and the addition of a new 
register (R2) in the coprocessor register map are the only alterations to the 
programmer's model.

Bit [4] of the debug control register is monitor mode enable, and controls how the device 
reacts on a breakpoint or watchpoint:

•

when set, the core takes the instruction or data abort exception

•

when clear, the core enters debug state.

Bit [5] of the debug control register is EmbeddedICE-RT disable. Setting this bit 
temporarily disables breakpoints and watchpoints, enabling the breakpoint or 
watchpoint registers to be programmed with new values. Clearing this bit makes the 
new breakpoint or watchpoint values operational.

The new register (R2) in the coprocessor register map indicates whether the processor 
entered the Prefetch or Data Abort exception because of either a real abort, or because 
of a breakpoint or watchpoint.

Ability to disable EmbeddedICE logic

Improvements have been made to the EmbeddedICE logic to ensure that when DBGEN 
is tied low, much of the EmbeddedICE logic is disabled to keep power consumption to 
a minimum.

Summary of Contents for ARM7TDMI































































































































































































































































































Reviews:

No comments

Related manuals for ARM7TDMI

Salto Node Installation Manual preview
Node
Brand: Salto Pages: 2
IBA Com-L2B-4-8 Manual preview
Com-L2B-4-8
Brand: IBA Pages: 29
ForeScout CounterACT Quick Installation Manual preview
CounterACT
Brand: ForeScout Pages: 28
FOR-A USF-105AS Operation Manual preview
USF-105AS
Brand: FOR-A Pages: 39
Zoom 4412A User Manual preview
4412A
Brand: Zoom Pages: 48
Daedalon EC-33 Instruction Manual preview
EC-33
Brand: Daedalon Pages: 6
C-Com IPAM-1600s Series User Manual preview
IPAM-1600s Series
Brand: C-Com Pages: 148
Patton electronics Model 2711 User Manual preview
Model 2711
Brand: Patton electronics Pages: 13
Balluff Easy Tool-ID BSG TID-05-T30-00-005 Installation And Operation Manual preview
Easy Tool-ID BSG TID-05-T30-00-005
Brand: Balluff Pages: 46
MEMON memonizerWORKSTATION Quick Start Manual preview
memonizerWORKSTATION
Brand: MEMON Pages: 2
AC Infinity AIRCOM Series User Manual preview
AIRCOM Series
Brand: AC Infinity Pages: 24
Microscan MS-96 Vial Reader User Manual preview
MS-96 Vial Reader
Brand: Microscan Pages: 67
Digital Equipment ChannelWorks Network Installer Manual preview
ChannelWorks
Brand: Digital Equipment Pages: 90
LST ZEB2-1 Specifications preview
ZEB2-1
Brand: LST Pages: 1
SmartBridges airPoint Nexus sB3210 User Manual preview
airPoint Nexus sB3210
Brand: SmartBridges Pages: 55
Mobatime DTS 4020.timebridge Mounting And Instruction Manual preview
DTS 4020.timebridge
Brand: Mobatime Pages: 94
Dinstar UC8000 IPPBX User Manual preview
UC8000 IPPBX
Brand: Dinstar Pages: 103
JOBO Lift CPE-3 Operating Instruction preview
Lift CPE-3
Brand: JOBO Pages: 12

Brands by name

Popular brands

Load more brands