manualshive.com logo in svg

ARM ARM7TDMI, Technical Reference Manual

The ARM ARM7TDMI User Manual is available for free download on our website. This comprehensive manual provides detailed instructions and guidelines on operating and optimizing your ARM7TDMI processor. Enhance your understanding of this product by downloading the user manual from manualshive.com.

Share
Download
background image

Debug in Depth 

B-58

Copyright © 2001, 2004 ARM Limited. All rights reserved.

ARM DDI 0210C

The address comparator output of the watchpoint is used to drive the write enable for 
the 

CHAINOUT

 latch. The input to the latch is the output of the data comparator from 

the same watchpoint. The output of the latch drives the 

CHAIN

 input of the breakpoint 

comparator. The address YYY is stored in the breakpoint register and when the 

CHAIN

 

input is asserted, the breakpoint address matches and the breakpoint triggers correctly.

B.18.2

RANGEOUT signal

The 

RANGEOUT

 signal is derived as follows:

RANGEOUT = ((({Av[31:0],Cv[4:0]} XNOR {A[31:0],C[4:0]}) OR {Am[31:0],Cm[4:0]}) == 0xFFFFFFFFF) AND 
((({Dv[31:0],Cv[7:5]} XNOR {D[31:0],C[7:5]}) OR 
Dm[31:0],Cm[7:5]}) == 0x7FFFFFFFF)

The 

RANGEOUT

 output of watchpoint register 1 provides the 

RANGE

 input to 

watchpoint register 0. This 

RANGE

 input enables you to couple two breakpoints 

together to form range breakpoints.

Selectable ranges are restricted to being powers of 2. For example, if a breakpoint is to 
occur when the address is in the first 256 bytes of memory, but not in the first 32 bytes, 
program the watchpoint as follows:

For Watchpoint 1: 

1.

Program Watchpoint 1 with an address value of 

0x00000000

 and an address mask 

of 

0x0000001F

. 

2.

Clear the ENABLE bit. 

3.

Program all other Watchpoint 1 registers as normal for a breakpoint. An address 
within the first 32 bytes causes the 

RANGE

 output to go HIGH but does not 

trigger the breakpoint.

For Watchpoint 0:

1.

Program Watchpoint 0 with an address value of 

0x00000000

 and an address mask 

of 

0x000000FF

. 

2.

Set the ENABLE bit. 

3.

Program the RANGE bit to match a 0. 

4.

Program all other Watchpoint 0 as normal for a breakpoint.

If Watchpoint 0 matches but Watchpoint 1 does not, that is the

 RANGE

 input to 

Watchpoint 0 is 0, the breakpoint is triggered.

Summary of Contents for ARM7TDMI































































































































































































































































































Reviews:

No comments

Related manuals for ARM7TDMI

NEC Univerge SV8100 System Configuration Manual preview
Univerge SV8100
Brand: NEC Pages: 44
Renesas Compact Emulator M30620T-CPE User Manual preview
Compact Emulator M30620T-CPE
Brand: Renesas Pages: 52
N.A.T. NAT-MCH Technical Reference Manual preview
NAT-MCH
Brand: N.A.T. Pages: 32
Lanner electronics EM-566 Series Manual preview
EM-566 Series
Brand: Lanner electronics Pages: 59
Buffalo LinkStation Quick Setup Manual preview
LinkStation
Brand: Buffalo Pages: 2
Kaptia Klever Getting Started preview
Klever
Brand: Kaptia Pages: 14
axing EOC 30-01 Quick Start Manual preview
EOC 30-01
Brand: axing Pages: 4
Arduino ABX00061 Reference Manual preview
ABX00061
Brand: Arduino Pages: 25
Divio SRA311-008P8 Series Installation Manual preview
SRA311-008P8 Series
Brand: Divio Pages: 4
Dataprobe iBoot Instruction Manual preview
iBoot
Brand: Dataprobe Pages: 16
PADAUK PDK5S-P-003 User Manual preview
PDK5S-P-003
Brand: PADAUK Pages: 27
Alcatel-Lucent Service Aggregation Router 7705 Installation Manual preview
Service Aggregation Router 7705
Brand: Alcatel-Lucent Pages: 20
Alphacool NexXxoS GPX-N 1070-M08 Instruction Manual preview
NexXxoS GPX-N 1070-M08
Brand: Alphacool Pages: 4
silicom TimeSync STS2 Hardware Installation Manual preview
TimeSync STS2
Brand: silicom Pages: 16
Emerson ControlWave Remote Ethernet I/O Product Data preview
ControlWave Remote Ethernet I/O
Brand: Emerson Pages: 3
Emerson SiteI/O 10/0 Specification preview
SiteI/O 10/0
Brand: Emerson Pages: 6
Emerson Bristol Helicoid Gauges Product Overview preview
Bristol Helicoid Gauges
Brand: Emerson Pages: 1
Emerson ACC/ARTM-7221/SCSI Installation Manual preview
ACC/ARTM-7221/SCSI
Brand: Emerson Pages: 62

Brands by name

Popular brands

Load more brands