manualshive.com logo in svg

Arcus-EDS 65001002, Manual, Page: 42 / 46

Share
Download
Arcus-EDS 65001002 Manual Download Page 42

Domestic Ventilation with Heat Recovery
KNX-LUNOS-CONTROL4

Subject to change

Arcus-EDS GmbH
www.arcus-eds.de

Rigaer Str. 88 10247 Berlin 
[email protected]

Tel.: +49(0)30 25933914
Fax.: +49(0)30 25933915

682x-Lunos-Control-4F

V.13.09.2022

e1

5. Commissioning

5.1 KNX-LUNOS-CONTROL4-IW

The KNX clamp is connected to the KNX bus via the supplied terminal block (red (+) / black (GND)). The
auxiliary voltage is connected via the supplied terminal block (yellow (+) / white (GND)). The fans are
mounted according to the lunos specification and connected via the supplied preceded connector.
Optionally, potential-free button / switch can be connected via the supplied connector.

Under no circumstances may the module be connected to mains voltage potential.No mains
voltage potential may be carried in the flush -mounted socket used. Installation may only be
carried out by a specialist.

The pre-assembled connector must be connected to the cables of the fans as follows

Fan connection

ACM-Module connection

violet

violet

0-10V

red

red

+12V

blue

blue

GND

Summary of Contents for 65001002















































Reviews:

No comments