manualshive.com logo in svg

APRILIA RSV 1000 R, Workshop Manual

Share
Download
APRILIA RSV 1000 R Workshop Manual Download Page 305

 

 

ELECTRICAL SYSTEM

7 - 17

RSV 

1000

 R - RSV 

1000

R FACTORY 

ADDITIONAL KEY STORE PROCEDURE 
 

The immobilizer system can recognize up to 4 keys. The 
storage procedure can only be done at the Dealer’s with a 
Master Key. 
The storage procedure cancels the existing codes, so that if 
the client wishes to store new keys he must come to the 
Dealer’s with all the keys he wishes to use. The storage pro-
cedure is as follows : 
1.  with a customer key (already stored), turn from key ON 

to OFF 

 
2.  fit the Master Key within 20 seconds, thus enabling the 

storing procedure. The led will stay on continuously 

 

 

3.  insert and run key-ON’s in sequence with all the keys to 

be stored. The led will switch off for 0.5 seconds after 
each key has been successfully stored. 

 
4.  After each key has been stored, the system waits for a 

new key for 20 seconds (led on continuously) after 
which the procedure self-terminates (the led flashes 
once for each key and then turns off). 

 

Summary of Contents for RSV 1000 R





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands