manualshive.com logo in svg

APRILIA RSV 1000 R, Workshop Manual

Share
Download
APRILIA RSV 1000 R Workshop Manual Download Page 229

 

 

CYCLE PARTS 

5 - 84 

RSV 

1000

R - RSV 

1000

 R FACTORY

5.5. SWINGING ARM 

5.5.1. 

REMOVING THE SWINGING ARM 

• 

Position the vehicle on its center stand 

(OPT)

. 

• 

Remove the rear wheel. 

IMPORTANT 

Although not required for removing the rear 

wheel, the rear stand 

(OPT)

 is necessary for supporting the 

swinging arm without the wheel mounted. 

Shim out the rear stand base 

(OPT)

 to bring it into position 

(engaged with the two pawls on the swinging arm itself). 

 

 

• 

Remove the exhaust assembly. 

• 

Loosen and remove the three screws securing the 
cover and collect the washers. 

 

 

• 

Move the mount plate complete with brake caliper and 
speed sensor (connected to their hose and cable re-
spectively) carefully to one side and rest it on the 
ground. 

 

 

WARNING 
Do not operate the rear brake lever with the 
brake caliper removed, or the brake caliper pis-
ton might fall out leading to loss of brake fluid.

 

 

 

 

• 

From the LH side, release and remove the double con-
necting link / swinging arm nut. 

• 

Extract the screw from the other side. 

 

 

Summary of Contents for RSV 1000 R





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands