En-14
9. TEST RUN
CHECK ITEMS
Is operation of each button on the remote controller normal?
(1)
Does each lamp light normally?
(2)
Do not air fl ow direction louvers operate normally?
(3)
Is the drain normal?
(4)
Is there any error noise and vibration during operation?
(5)
Do not operate the air conditioner test run for a long time.
•
CHECKING DRAINAGE
.
To check the drain, remove the water cover and fi ll with 1 liter of water as shown in the
fi gure.
The drain pump operates when operating in the cooling mode.
Drain pipe
Wire cover
Screw
Watering pot
• Test running
When the air conditioner is
run by pressing the remote controller test run button,
the OPERATION and TIMER lamps fl ash slowly at the same time.
[Operation method]
For the operation method, refer to the operating manual.
•
The outdoor unit may not operate depending on the room temperature.
•
In this case, press the TEST RUN button on the remote controller while the air condi-
tioner is running. (Point the transmitter section of the remote controller toward the air
conditioner and press the TEST RUN button with the tip of a ball-point pen, etc.)
Transmitter section
TEST RUN button
To end test operation, press the remote controller START/STOP button.
•
(When the air conditioner is run by pressing the TEST RUN button, the OPERATION
Lamp and TIMER Lamp will simultaneously fl ash slowly.)
[Using the wired remote control] (Option)
For the operation method, refer to the operating manual.
•
Stop the air conditioner operation.
(1)
Press the MODE button and the FAN button simultaneously for 2 seconds or more to
(2)
start the test run.
Test run display
Press the START/STOP button to stop the test run.
(3)
If “C0” appears in the R.C. address display, there is a remote controller error. Refer to the
installation manual included with the remote controller.
R.C. address
Error code
Content
Incompatible indoor unit is connected
Indoor unit
↔
remote controller com-
munication error
10. CHECK LIST
Pay special attention to the check items below when installing the indoor unit(s). After
installation is complete, be sure to check the following check items again.
CHECK ITEMS
If not performed
correctly
CHECK
BOX
Has the indoor unit been installed
correctly?
Vibration, noise, indoor unit
may drop
Has there been a check for gas
leaks (refrigerant pipes)?
No cooling, No heating
Has heat insulation work been
completed?
Water leakage
Does water drain easily from the
indoor units?
Water leakage
Are the wires and pipes all con-
nected completely?
No operation, heat or burn
damage
Is the connection cable the speci-
fi ed thickness?
No operation, heat or burn
damage
Are the inlets and outlets free of any
obstacles?
No cooling, No heating
After installation is completed, has
the proper operation and handling
been explained to the user?
11. OPTIONAL KIT INSTALLATION (OPTION)
WARNING
Regulation of cable differs from each locality, refer in accordance with local rules.
This air conditioner can be connected with the following optional kits.
Option type
Connector No.
Fresh air intake
CN6
External input
CN102
External output
CN103
Wired Remote Controller
-
Fresh air intake kit
Wired Remote Controller
External output kit
External input kit
12. CUSTOMER GUIDANCE
Explain the following to the customer in accordance with the operating manual:
Starting and stopping method, operation switching, temperature adjustment, timer, air
(1)
fl ow switching, and other remote controller unit operations.
Air fi lter removal and cleaning, and how to use the air louvers.
(2)
Give the operating and Installation Manuals to the customer.
(3)
If the signal code is changed, explain to the customer how it changed (the system
(4)
returns to signal code A when the batteries in the remote controller unit are replaced).
*(4) is applicable to using wireless remote controller.
9379124010-05_IM.indb 14
9379124010-05_IM.indb 14
8/31/2012 10:43:35 AM
8/31/2012 10:43:35 AM
AMP Air Conditioning
www.ampair.co.uk | [email protected]
