AMF REECE S-311, Parts And Service Manual, Page: 93 / 142

S-311+ ACL
1-7 ACL
A - INTRODUCTION
Released: 01/2014
E-mail: service@amfreece.cz; webside: amfreece.com
Phone: +420 582 309 146; Fax: +420 582 360 606
3. TECHNICAL SPECIFICATION
* Note: If you use threads 100 or less strong, the manufacturer recommends using left looper (order number 17.0069.4.019).
If you use low quality threads, they can burn in the needle area (in such case the manufacturer recommends lowering machine
speed - rotation).
Machine type/model
AF/ACL
3,0 - 20,0 mm
4 - 8 mm
4 - 20
4 - 20
12 mm
Up to 8,0 mm
Cut before (CB), cut after (CA), no cutt (OFF), partial cutting (LP1 a LP2)
From - 0,50 up to + 1,2 mm
See section D 5 (manual S-311)
Without eye; 2,2 x 3,0 mm; 2,8 x 4,2 mm; 3,0 x 4,6 mm; 3,2 x 5,0 mm; 3,4 x 4,2 mm
2,1 mm (AF, LTT), ( ± 0,3 mm elektronically); 2,7 mm (± 0,3 mm elektronically)
2,1 mm (AF, LTT), ( ± 0,5 mm elektronically); 2,7 mm (± 0,5 mm elektronically)
± 1,5 mm
64 mm
02.0558.0.111 (Nm 100)
80, 100, 120, gimp 30-100.
0,55 MPa = 80 PSI
530 mm (hight) x 370 mm (width) x 560 mm (depth)
730 mm (hight) x 1100 mm (width) x 700 mm (depth) + 150 mm uplift
64 kg
175 kg
1NPE~60Hz 230 V/TN/S; 1NPE~50Hz 230 V/TN/S
Min. 10A Charakteristik C (EN60947-2)
L =86,9db; L =74,8 db; measured according EN ISO 3746:1995
wA pfA
According to IEC 364-3, IEC 364-5-51 temperature from +5°C to 40°C, relative humidity from 30 to 80%
13 - 38 mm 13 - 26 mm 13 - 30 mm
1000 - 2000 stitches per minute (500 - 1000 rotation per minute of the drive shaft)
0,5 - 2,0 mm (each step 0,1 mm)
Performance of the machine
Cutting lenght
Type of buttonhole
Type of eye
Lenght of fly bar
Lenght of cross bar
Number of stitch in the eye
Number of stitches in round end
Upstroke of clamp feet (max)
Thickness of the work piece (max)
Cutting
Cutting space
Correction of cutting lenght
Movement of the bedplate
Needle
Recommendet threads*
Bottom thread and gimp timming
Trimming range
Operational conditions
Air pressure
Noise level
Dimension of the machine head
Weight of the machine head
Dimension of the machine stand
Total weight of the machine
Electricity power connection
Circuit breaker
Electronic bite
(width of sewing)
Electronic bite
(cross bar)
Buttonhole
lenght
AF/ACL-LP1 AF/ACL-LPE
L = 3 - 7 mm
0,5 - 1,5 mm Density of cross bar
Upper thread trimming
13 - 30 mm
AF/ACL-LP2
Stitch density
13 - 38 mm 5 - 21 mm 6 - 30 mm 12 - 25 mm