American Megatrends Excalibur PCI User Manual Download Page 78

Page: 78 / 102

Chapter 6 WinBIOS Setup

Peripheral Setup,

Continued

On-Board Floppy Drive

This option enables the use of the floppy drive controller on the motherboard (if installed). The settings are

Enabled

Disabled.

On-Board IDE Drive

This option enables the use of the IDE controller on the motherboard (if installed). The settings are

Enabled

Disabled.

First Serial Port Address

IRQ4 is used for the first serial port (COM1). This option enables serial port 1 on the motherboard (if installed). The
settings are

2E8h.

Second Serial Port Address

IRQ3 is used for the second serial port (COM2). This option enables serial port 2 on the motherboard, if installed. The
settings are

2E8h

Parallel Port Address

IRQ7 is used for the parallel port (LPT1). The IRQ can be changed to IRQ5. This option enables the parallel port on
the motherboard, if installed. The settings are

278h

IRQ Active State

This option specifies if the parallel and serial port IRQs are active high or active low. The settings are

Low

High.

Parallel Port Mode

This option specifies the parallel port Mode. The settings are

Normal

Extended.

Summary of Contents for Excalibur PCI







































































































Search results

Summary of Contents for Excalibur PCI

Reviews:

Related manuals for Excalibur PCI

Brands by name

Popular brands

American Megatrends Excalibur PCI, User Manual

Search results

Summary of Contents for Excalibur PCI

Reviews:

Related manuals for Excalibur PCI

Brands by name

Popular brands