American Megatrends Excalibur PCI User Manual Download Page 46 | Manualshive

Page: 46 / 102

background image

Chapter 4 Installation

54

Step 11 Install Adapter Cards

The Excalibur PCI Pentium motherboard provides full compatibility with all IBM XT and AT-compatible adapter
cards via four ISA (AT-compatible) expansion slots. The Excalibur PCI Pentium motherboard also has three PCI
Local Bus expansion slots. A summary of the slots follows.

PCI Local Bus Expansion Slots

The PCI Local Bus expansion slot sockets are distinctly different than the standard ISA expansion slot sockets. These
slots obviously accept a different kind of adapter card than the standard ISA adapter cards. The slots are much more
compact and smaller. PCI Slot 1 and Slot 2 are master slots. Slot 3 is a slave-only slot.

ISA Adapter Cards

Two sets of pinouts are provided in the following pages for ISA expansion slot sockets.

The first is the 8-bit pinout that accepts PC- and XT-compatible adapter cards.

The second is the 16-bit extension to the 8-bit sockets that, together with the 8-bit sockets, accept 16-bit ISA adapter
cards.

«
...
44
45
46
47
48
...
»

Summary of Contents for Excalibur PCI







































































































Reviews:

No comments

Related manuals for Excalibur PCI

Brand: Xilinx Pages: 23

Brand: Xilinx Pages: 60

Brand: Xilinx Pages: 41

Zynq UltraScale+ ZCU104

Brand: Xilinx Pages: 92

Zynq UltraScale+ ZCU104

Brand: Xilinx Pages: 4

Spartan-3A DSP FPGA Series

Brand: Xilinx Pages: 10

Brand: Xilinx Pages: 92

Brand: Texas Instruments Pages: 30

Brand: Supero Pages: 105

AR0140CS2M00AUEAH3-GEVB

Brand: ON Semiconductor Pages: 5

Brand: SOYO Pages: 95

MITX-DNV0 Series

Brand: Quanmax Pages: 84

Brand: Biostar Pages: 71

Brand: Aaeon Pages: 97

Brand: Fujitsu Siemens Computers Pages: 42

Brand: Gigabyte Pages: 120

Brand: ON Semiconductor Pages: 20

Brand: R&S Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands