American Megatrends Excalibur PCI User Manual Download Page 48

Page: 48 / 102

Chapter 4 Installation

Step 11 Install Adapter Cards,

Continued

16-Bit ISA Extension Pinout

The following 16-bit pins are an extension of the 8-bit adapter card layout and are used in conjunction with the
standard 8-bit pins.

Pin

Use

Pin

Use

SBHE-

MEMCS16-

LA23

IOCS16-

LA22

IRQ10

LA21

IRQ11

LA20

IRQ12

LA19

IRQ15

LA18

IRQ14

LA17

DACK0-

MEMR-

DREQ0

C10

MEMW-

D10

DACK5-

C11

SD08

D11

DREQ5

C12

SD09

D12

DACK6-

C13

SD10

D13

DREQ6

C14

SD11

D14

DACK7-

C15

SD12

D15

DREQ7

C16

SD13

D16

C17

SD14

D17

MASTER-

C18

SD15

D18

GND

PCI Local Bus Pinout

The first three expansion slots in the Excalibur PCI Pentium motherboard are for PCI Local Bus adapter cards, as
shown on the graphic on page 19. The PCI bus master slots are P16 (Slot1) and P17 (Slot2). The PCI slave expansion
slot is P18 (Slot3).

Summary of Contents for Excalibur PCI







































































































Search results

Summary of Contents for Excalibur PCI

Reviews:

Related manuals for Excalibur PCI

Brands by name

Popular brands

American Megatrends Excalibur PCI, User Manual

Search results

Summary of Contents for Excalibur PCI

Reviews:

Related manuals for Excalibur PCI

Brands by name

Popular brands