American Megatrends Excalibur PCI User Manual Download Page 18 | Manualshive

Page: 18 / 102

background image

Chapter 4 Installation

18

Chapter 4

Installation

Unpacking the Motherboard

Step

Action

1

Inspect the cardboard carton for obvious damage. If
damaged, call Technical Support at 404-246-8600. Leave
the motherboard in its original packing.

2

Perform all unpacking and installation procedures on a
ground-connected anti-static mat. Wear an anti-static
wristband, grounded at the same point as the anti-static mat
or use a sheet of conductive aluminum foil grounded
through a 1 megohm resistor instead of the anti-static mat.
Similarly, a strip of conductive aluminum foil wrapped
around the wrist and grounded through a 1 megohm resistor
serves the same purpose as the wristband.

3

Inside the carton, the motherboard is packed in an
anti-static bag and sandwiched between sheets of sponge.
Remove the sponge and the anti-static bag. Place the
motherboard on a grounded anti-static surface component
side up. Save the original packing material in case of
reshipment.

4

Inspect the motherboard for damage. Press down on all ICs
mounted in sockets to verify proper seating. Do not apply
power to the motherboard if it has been damaged.

5

If the motherboard is undamaged, it is ready to be installed.

«
...
16
17
18
19
20
...
»

Summary of Contents for Excalibur PCI







































































































Reviews:

No comments

Related manuals for Excalibur PCI

Brand: Yamaha Pages: 232

RTKA223012DR0050BU

Brand: Renesas Pages: 14

Brand: JETWAY Pages: 52

Brand: JETWAY Pages: 48

Brand: IEI Technology Pages: 140

Brand: IBASE Technology Pages: 84

Brand: Gigabyte Pages: 87

SERVER SYSTEM SR2500AL

Brand: Intel Pages: 210

Brand: BiPOM Electronics Pages: 12

Brand: IEI Technology Pages: 160

Brand: Advantech Pages: 124

Brand: Micronics Pages: 63

Brand: Texas Instruments Pages: 24

Brand: Rosch Computer Pages: 43

Brand: TYAN Pages: 130

Brand: Ebyte Pages: 9

Brand: Gigabyte Pages: 147

Brand: u-blox Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands