American Megatrends Excalibur PCI User Manual Download Page 16

Page: 16 / 102

Chapter 3 Specifications

Onboard I/O

Universal Peripheral Controller

The Excalibur PCI motherboard has an SMC FDC37C665 Universal Peripheral Controller that supports up to two

floppy drives (360 KB, 1.2 MB, 720 KB, 1.44 MB, or 2.88 MB), two serial ports (using National Semiconductor
16C550s), and one parallel port with ECP (Extended Capabilities Port) and EPP (Enhanced Parallel Port) capability.

Onboard PCI IDE Support

The onboard IDE is on the PCI bus. The IDE controller supports IDE Mode 0, Mode 1, Mode 2, and Mode 3. It also

supports IDE read data prefetch and write posting. The AMIBIOS supports 32-bit data transfers as well as the following
cycle times for each IDE Mode.

IDE Mode

Cycle Time (in nanoseconds)

600

383

240

180

PCI IDE Support on the PCI Expansion Slots

PCI IDE adapter cards that require IRQ14 are supported only in PCI Slot1 (P16).

SW1-8 must be set ON to enable IRQ14.

Summary of Contents for Excalibur PCI







































































































Search results

Summary of Contents for Excalibur PCI

Reviews:

Related manuals for Excalibur PCI

Brands by name

Popular brands

American Megatrends Excalibur PCI, User Manual

Search results

Summary of Contents for Excalibur PCI

Reviews:

Related manuals for Excalibur PCI

Brands by name

Popular brands