Amazone ZA-V Operating Manual Download Page 83

Page: 83 / 136

Coupling and uncoupling the machine

ZA-V BAG0087.11 01.20

Coupling and uncoupling the machine

When coupling and decoupling the machine, comply with the chapter

"Safety information for the user", page 23.

WARNING
Danger from crushing, catching, entanglement and / impacts

caused by unintentional starting and rolling of the tractor when

the tractor's PTO shaft and supply lines are coupled or decou-

pled!

Secure the tractor and machine against unintentional start-up and

rolling, before entering the danger area between the tractor and ma-

chine when coupling or decoupling the PTO shaft. See page 80.

WARNING
Danger from crushing and impacts between the rear of the trac-

tor and the machine during coupling/uncoupling.

•

It is prohibited to operate the tractor's 3-point hydraulic system

while persons are present between the rear of the tractor and

the machine.

•

Only actuate the operator controls for the tractor's three-point

hydraulic system

from the intended workstation beside the tractor.

if you are outside of the danger area between the tractor

and the machine.

Summary of Contents for ZA-V









































































































































Search results

Summary of Contents for ZA-V

Reviews:

Amazone ZA-V, Operating Manual, Page: 83 / 136

Search results

Summary of Contents for ZA-V

Reviews: