manualshive.com logo in svg

Amazone ZA-V, Operating Manual, Page: 29 / 136

Share
Download
Amazone ZA-V Operating Manual Download Page 29

 

 

 

 

General safety instructions 

 

ZA-V  BAG0087.11  01.20

 

29 

 

2.16.5  Fertiliser spreader operation 

 

•

 

Stay clear of the working area! Danger from flying fertiliser parti-

cles. Direct persons away from the throwing range of the fertilis-

er spreader. Do not walk or stand close to rotating spreading 

discs. 

•

 

Fill the fertiliser spreader only when the tractor engine is shut off, 

the ignition key is pulled and the sliders are closed. 

•

 

Do not place any foreign objects in the hopper. 

•

 

While carrying out the spread rate check, beware of danger 

points from rotating machine parts. 

•

 

Never unhitch a fertiliser spreader or roll it while it is full (tipping 

hazard). 

•

 

For boundary spreading at field edges, bodies of water or roads, 

use boundary spreading devices. 

•

 

Before each use, ensure that the attachment parts are properly 

fitted, particularly those for attaching the spreading discs and 

spreading vanes. 

2.16.6  Cleaning, maintenance and repairs 

 

•

 

Only carry out cleaning, maintenance and repair work on the 

machine when: 

ο

 

The drive is switched off 

ο

 

The tractor engine has come to a complete stop 

ο

 

The ignition key has been removed 

ο

 

The machine connector has been removed from the control 

computer 

•

 

Regularly check the nuts and bolts for a firm seat and retighten 

them as necessary. 

•

 

Secure the raise machine and/or raised machine parts against 

unintentional falling, before cleaning, maintaining or repairing the 

machine. 

•

 

When replacing work tools with blades, use suitable tools and 

gloves. 

•

 

Dispose of oils, greases and filters in the appropriate way. 

•

 

Disconnect the cable to the tractor generator and battery, before 

carrying out electrical welding work on the tractor and on at-

tached machines. 

•

 

Spare parts must meet at least the specified technical require-

ments of AMAZONEN-WERKE. This is ensured through the use 

of original 

AMAZONE

 spare parts. 

Summary of Contents for ZA-V









































































































































Reviews:

No comments