manualshive.com logo in svg

Amazone ZA-V, Operating Manual, Page: 15 / 136

Share
Download
Amazone ZA-V Operating Manual Download Page 15

 

 

 

 

General safety instructions 

 

ZA-V  BAG0087.11  01.20

 

15 

 

2.10.1  Spare and wear parts and aids 

 

Immediately replace any machine parts which are not in a perfect 

state. 
Only use AMAZONE spare and wear parts released by AMAZONEN-

WERKE, so that the type approval remains valid according to the 

national and international regulations. The use of wear and spare 

parts from third parties does not guarantee that they have been con-

structed in a way as to meet the requirements placed on them. 
AMAZONEN-WERKE shall accept no liability for damage caused by 

the use of unreleased spare and wear parts or aids. 

2.11 

Cleaning and disposal 

 

Handle and dispose of any materials used carefully, in particular 

•

 

When carrying out work on lubrication systems and equipment 

and 

•

 

When cleaning using solvents. 

2.12 

User workstation 

 

The machine may only be operated by one person sitting in the driv-

er's seat of the tractor. 

Summary of Contents for ZA-V









































































































































Reviews:

No comments