Amazone ZA-V Operating Manual Download Page 51

Page: 51 / 136

Structure and function

ZA-V BAG0087.11 01.20

•

Observe the maximum approved hydraulic operating pressure of

210 bar.

•

Check the compatibility of the hydraulic fluids before connecting

the machine to the hydraulic system of your tractor.

•

Do not mix any mineral oils with biological oils.

•

Slide the hydraulic connector(s) into the hydraulic sleeves until

they are heard to engage.

•

Check the coupling points of the hydraulic hose lines for a cor-

rect, tight seat.

•

Coupled hydraulic hose lines

must easily give way to all movements in bends without

tensioning, kinking or rubbing.

must not rub against other parts.

1. Swivel the actuation lever on the control valve on the tractor to

float position (neutral position).

2. Clean the hydraulic plug for the hydraulic hose lines before con-

necting them to the tractor.

3. Couple the hydraulic hose lines with the tractor control units.

5.9.2

Uncoupling the hydraulic hose lines

1. Swivel the actuation lever on the control valve on the tractor to

float position (neutral position).

2. Unlock the hydraulic connectors from the hydraulic sockets.
3. Safeguard the hydraulic sockets against soiling with the dust

protection caps.

4. Insert the hydraulic plug into the plug holder.

Summary of Contents for ZA-V









































































































































Search results

Summary of Contents for ZA-V

Reviews:

Amazone ZA-V, Operating Manual, Page: 51 / 136

Search results

Summary of Contents for ZA-V

Reviews: