Amazone ZA-V Operating Manual Download Page 41

Page: 41 / 136

Structure and function

ZA-V BAG0087.11 01.20

5.3

Spreading discs with spreading vanes

An infinite adjustment of the working widths is

possible by

•

swivelling the spreading vanes onto the

spreading discs,

•

replacing the spreading vanes on the

spreading discs.

In the case of the ZA-V, the spreading discs and

agitators are powered by the PTO shaft via the

middle gearbox and angular gearbox.

Fig. 11

Looking in the direction of travel:
(1)  Left spreading disc
(2)  Right spreading disc
(3)  Long spreading vane - Adjustment scale

with values from 35 to 55.

(4) Short spreading vane – Adjustment scale

with values from 5 to 25.

Fig. 12

Markings on spreading disc

Example of a marking:

V2 K LI

Fig. 13

Spreading vane

Mounting side

V1
V2
V3

L = Long

=
=

right

left

K = Short

=
=

right

left

The spreading vanes are installed in such a way that the open sides

point in the direction of rotation and take in the fertiliser.

Configure the settings using the information in the setting chart. You

can easily check the configured working width using the mobile ferti-

liser test rig (optional).

Summary of Contents for ZA-V









































































































































Search results

Summary of Contents for ZA-V

Reviews:

Amazone ZA-V, Operating Manual, Page: 41 / 136

Search results

Summary of Contents for ZA-V

Reviews: