Amazone ZA-V Operating Manual Download Page 48

Page: 48 / 136

Structure and function

ZA-V BAG0087.11 01.20

5.8.2

Uncoupling the PTO shaft

WARNING
Danger from crushing or impact if there is insufficient clearance

when uncoupling the PTO shaft!

First uncouple the machine from the tractor before uncoupling the

PTO shaft from the tractor. This will ensure the necessary clearance

for safe uncoupling of the PTO shaft.

WARNING
Danger from burns on hot components of the PTO shaft!

Do not touch components of the PTO shaft that have become hot

(particularly clutches).

•

After decoupling the PTO shaft, place it on the holder provided.

This protects the PTO shaft from damage and dirt.

•

Clean and lubricate the universal joint shaft if it will not be used

for an extended period.

1. Uncouple the machine from the tractor. Also

refer to the chapter "Uncoupling the ma-

chine", page 86.

2. Drive the tractor up to the machine, leaving

a clearance of approximately 25 cm be-

tween the tractor and the machine.

3. Secure the tractor against unintentional

starting and rolling away, see the chapter

"Securing the tractor against unintentional

starting and rolling away", from page 80.

4. Pull the latch of the PTO shaft off the uni-

versal joint shaft of the tractor. Observe the

operating manual supplied with the PTO

shaft when uncoupling the PTO shaft.

5. Place the PTO shaft in the holder provided

(Fig. 19).

6. Clean and lubricate the universal joint shaft

if it is not going to be used for a longer peri-

od of time.

Fig. 20

Summary of Contents for ZA-V









































































































































Search results

Summary of Contents for ZA-V

Reviews:

Amazone ZA-V, Operating Manual, Page: 48 / 136

Search results

Summary of Contents for ZA-V

Reviews: