manualshive.com logo in svg

Amazone Pantera 4503, Operating Manual

Share
Download
Amazone Pantera 4503 Operating Manual Download Page 83

 

 

 

 

Settings 

 

ISOBUS field sprayer  BAG0171.9  11.20

 

83 

 

Allocation 

 

 

 

 

 

< 

EDGE NOZZLE BODY

 

Each nozzle is shown with the parameters that 
have been entered. 

 

  1.  Select the nozzle for configuration. 

  2.  Confirm the entry. 

 

 

 

 

  3.  Make the entries for the nozzle. 

•

 

Nozzle size (with color-coding) 

•

 

Boundary nozzle. 

 

 

 

< 

EDGE NOZZLE BODY

 

 

Nozzle size 

 

 

Edge nozzle 

 

Boundary nozzle allocation 

 

 

 

 

 

 

BOUNDARY NOZZLE ALLOCATION

 

Which boundary nozzle will be switched on, with 
which standard nozzle from the standard nozzle 
body? 

 

  1.  Mark an angular field for the boundary noz-

zle. 

  2.  Enter the position of the boundary nozzle 

(1-4) that will be switched simultaneously 
with the standard nozzle (1-4). 

 

 

 

 

 

Summary of Contents for Pantera 4503

























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands