Amazone Pantera 4503 Operating Manual Download Page 76

Page: 76 / 120

Settings

ISOBUS field sprayer BAG0171.9 11.20

5.2.9.1

Nozzle body

The nozzle bodies must be fitted according to

•

the possible nozzle combination, see "automated processes"

•

the nozzle size, see table.

Small nozzle

Medium-sized nozzle Large nozzle

Nozzle 1, nozzle 4

Nozzle 3

Nozzle 2

If the nozzle spacing is 25 cm in the nozzle body, equip nozzle 1 and
2 with the same nozzles.

NOZZLE BODY

•

25 cm nozzle spacing



Yes, displacement kit 25 cm present



no, 20 ft / 50 cm

10 ft /

25 cm nozzle spacing

Display 50 cm nozzle spacing:

Display 25 cm nozzle spacing:

•

Enter parameters of the nozzle

Each nozzle is shown with the parameters that
have been entered.

1. Tap the nozzle for configuration.

Nozzle spacing 25 cm: Nozzle 1 and 2 will be
configured together.

Summary of Contents for Pantera 4503

























































































































Search results

Summary of Contents for Pantera 4503

Reviews:

Brands by name

Popular brands

Amazone Pantera 4503, Operating Manual

Search results

Summary of Contents for Pantera 4503

Reviews:

Brands by name

Popular brands