Amazone Pantera 4503 Operating Manual Download Page 59

Page: 59 / 120

Settings

ISOBUS field sprayer BAG0171.9 11.20

5.1.2

Spray liquid circuit

SPRAY LIQUID CIRCUIT

•

Front tank



Front tank with FlowControl in use



Front tank not in use

Front tank

•

Enter the minimum fill level in the spray
liquid tank when spraying (10-40%).

The minimum fill level in the spray liquid

tank is maintained via the front tank.

→

This can affect the front axle load of the
tractor.

Min. fill level in the spray

liquid tank when spraying

Flow meter 1

Flow meter 2 (return flow meter)

Flow meter 3 (High Flow+)

•

Enter the pulses for the flow meter
(0-9999)

•

Calibrate flow meters

Pulses

flow meter 1

Calibrate

flow meter 1

Pulses

flow meter 2

Calibrate

flow meter 2

Pulses

flow meter 3

Calibrate

flow meter 3

Calibrating flow meters

•

The machine computer needs the calibration value "Pulse flow
meter" for the flow meter / return flow meter to determine and
control the rate.

•

You must determine the calibration value "Pulse flow meter" via
a calibration procedure of the flow meter / return flow meter, if
the calibration value is not known.

•

You can enter the calibration value, "Pulse flow meter" for the
flow meter / return flow meter manually if you know the precise
calibration value.

Summary of Contents for Pantera 4503

























































































































Search results

Summary of Contents for Pantera 4503

Reviews:

Brands by name

Popular brands

Amazone Pantera 4503, Operating Manual

Search results

Summary of Contents for Pantera 4503

Reviews:

Brands by name

Popular brands