manualshive.com logo in svg

Amazone Pantera 4503, Operating Manual

Share
Download
Amazone Pantera 4503 Operating Manual Download Page 45

 

 

 

 

Field menu 

 

ISOBUS field sprayer  BAG0171.9  11.20

 

45 

 

Display in the Work menu: 

 

 

AutoTrail in manual mode 

 (1)  Pilot control for steering counter to the 

slope 

 (2)  Actual axle position 

 (3)  Axle steered to the right 

 (4)  Axle steered to the left 

 (5)  Axle in straight ahead position 

 

 

 

AutoTrail in automatic mode displaying the steer-
ing angle. 

 

 

AutoTrail in road mode, steering locked 

(Forward speed greater than 7 km/h). 

 

 

AutoTrail in road mode, steering unlocked 

 Steering can be unlocked when the 

forward speed is less than 7 km/h.  

 

Prohibited on public roads!

 

 When the sprayer boom is folded-out, the 

steering is automatically unlocked. 

 

 

AutoTrail with reduced steering angle due to high 
forward speed 

 

 

Safety-critical error 

•

 

Can be manually steered up to 7 km/h (for 
troubleshooting only). 

•

 

Contact the dealer. 

 

 

 

 

WARNING 

Risk of accident due to safety-critical AutoTrail error. 

Driving on public roads is prohibited. 

 

Summary of Contents for Pantera 4503

























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands