manualshive.com logo in svg

Amana A1200S, Service, Page: 53 / 75

Share
Download
Amana A1200S Service Download Page 53

53

RE220002   Rev. 6

A1200S, A1225S Programming Instructions

To avoid risk of electrical shock, personal injury, or death,
disconnect power to unit and discharge the capacitor
before following any disassembly procedures.

WARNING

!

Bar Code (UPC) Cooking

The Scanner Oven cooks food products by reading the
UPC symbol.

NOTE: "READY TO SCAN" flashes when the oven is

idle.

1. Open door to activate oven.
2. Scan food product's UPC by centering the UPC in

front of oven's scanner window no more than one-
half inch from the oven.

• A beep indicates the UPC was correctly read;

"PLACE FOOD IN OVEN" flashes in the Display
Window.

• No beep indicates the UPC was not read; rescan

the UPC.

• Rapid beeping indicates the UPC is not entered

into the oven's memory, the Display window will
flash "NOT IN MEMORY".

3. The Display Window will show "PLACE FOOD IN

OVEN" which indicates the time is set to cook 1
food item.  To cook 2 to 4 of the same food item,
push the appropriate quantity pad (X2, X3, X4)
once.  Pushing a quantity twice will cancel the
multiple quantity cooking and the display window will
read "QTY 1".

4. Place food in oven and close the door.  the oven will

start automatically and the Display Window will
show the time counting down.

NOTE:  Opening the door during cooking will stop the

cooking and the Display Window will flash
"RESUME OR CANCEL".  when the door is
closed, the oven will resume cooking.

NOTE: If two-stage cooking is programmed, the

Display Window will show the time for both
stages.

5. When the cooking is complete, the oven will beep

for 60 seconds or until the door is opened.  The
Display Window will flash "READY TO ENJOY'" until
the door is opened.  Open the door to take the food
and the display will flash "THANK YOU" one time.
After 60 seconds the Display Window continues to
display "READY TO ENJOY" after the door is
opened.

6. Close the door and the Display Window will flashes

"READY TO SCAN".

Manual Cooking

The following is an example of how to enter a cooking
cycle of one minute, thirty seconds at 50% power.
1. Place the removable onto the Scanner Panel.
2. Open the door and place the food item on the oven

shelf.

3. Press the time pad,  ":" displays.
4. Press number 1 pad, "  : 1" displays.
5. Press number 3 pad, "  :13" displays.
6. Press number 0 pad, " 1:30" displays.
7. Press power (Pwr) pad, "PWR 100" displays.
8. Press power (Pwr) pad until display window shows

"50",  "PWR 50" displays.

9. Close the door.  When cooking is complete, the oven

will beep for 60 seconds or until the door is opened,
and the Display Window will flash "READY TO
ENJOY" until the door is opened.

10. Open the door, remove the food and the Display

Window will flash "THANK YOU" once.

NOTE: Opening the door during cooking will stop the

cooking and the Display Window will flash
"RESUME OR CANCEL".  When the door is
closed, the oven will resume cooking.

11. Close the door and the Display window will flash

"READY TO SCAN".

Manual Cooking with Defrost

Defrost may be selected by pressing the defrost (Def)
pad.  The Display Window will show "PWR DF".  The
defrost cycle is divided into four power levels.
The following is an example of a defrost cycle for two
minutes.  The oven will automatically defrost for:

30 seconds at 80% power, then
30 seconds at 60% power, then
30 seconds at 40% power, then
30 seconds at 20% power.

1. Place the removable onto the Scanner Panel.
2. Open the door and place the food item on the oven

shelf.

3. Press the time pad,  ":" displays.
4. Press number 2 pad, "  : 2" displays.
5. Press number 0 pad, "  :20" displays.
6. Press number 0 pad, " 2:00" displays.
7. Press defrost (Def) pad, "PWR DF" displays.
9. Close the door.  When cooking is complete, the oven

will beep for 60 seconds or until the door is opened,
and the Display Window will flash "READY TO
ENJOY" until the door is opened.

10. Open the door, remove the food and the Display

Window will flash "THANK YOU" once.

Summary of Contents for A1200S












































































Reviews:

No comments