manualshive.com logo in svg

Amana A1200S, Service, Page: 51 / 75

Share
Download
Amana A1200S Service Download Page 51

51

RE220002   Rev. 6

A1200S, A1225S Programming Instructions

To avoid risk of electrical shock, personal injury, or death,
disconnect power to unit and discharge the capacitor
before following any disassembly procedures.

WARNING

!

NEW—This message is displayed to indicate that the
UPC just scanned has not been previously stored in
memory.

QTY 1, QTY 2, QTY 3, QTY 4—Each of these
messages indicates the quantity of food items to be
cooked.

COUNT—Total UPC cook count information is stored in
the memory and may be viewed by entering code 612.

PRINT—Total UPC cook counts may be accessed by
entering code 611.

REMOVABLE KEYPAD—This oven is shipped with the
removable keyboard packed in the USE AND CARE
manual.  The removable keyboard has a special
adhesive on the back side for easy installation and
removal.
NUMBER PADS (0-9)—Used to enter numbers into the
Display  Window.
POWER PAD (Pwr)—Used to enter power levels.
When pressed, the Display Window show "PWR 100";
holding down the Power Pad will slew the power level
from 100% down to 10%.
DEFROST PAD (Def)—When pressed, the Display
Window message is "PWR DF".  The defrost time is
divided into four power levels (80%, 60%, 40%, 20%).
TIME PAD (Time)—Used to enter time into the Display
Window.
DELETE PAD (Del)—Used to remove a UPC
associated recipe from scanner memory.
CHANGE PAT (Chg)—Used to change recipe or time in
memory.
ENTER PAD (Entr)—Used to start the recipe while
programming or to start cooking when using manual
cooking.

Removable Keyboard Installation

When programming is complete the Removable Keyboard
can be stored for future programming.
After reinstalling  backing material, place the Removable
Keyboard in the USE AND CARE manual.

1. Remove the backing material from the backside of the

removable keyboard as shown below.

Removable Keyboard (Back View)

2. To install the Removable Keyboard onto the Scanner

Panel:  align the bottom of the Removable Keyboard
with the inside bottom of the Scanner Panel and press
the Removable Keyboard into place.

3. The oven is ready to be programmed.

Summary of Contents for A1200S












































































Reviews:

No comments