manualshive.com logo in svg

Amana A1200S, Service, Page: 35 / 75

Share
Download
Amana A1200S Service Download Page 35

35

RE220002 Rev. 6

Troubleshooting Procedures

To avoid risk of electrical shock, personal injury, or death,
disconnect power to unit and discharge the capacitor
before following any disassembly procedures.

WARNING

!

Diagnosis for VEND-10.F, .G

Test Sequence 7:  Vari-Power Condition

Open oven door, place a cup of cool water in 
oven, close door, push button one and note 
time in display, open door and program 
button one for one minute of defrost, push 
button one.

Oven starts and times down, cavity light 
changes brillance and the oven sound 

Oven operates  on high only or does not heat at all.

varies in intensity (pulses) twice 
approximately every 12 seconds indicating 
defrost operation, the water is warmed?

No

1.
2.

Inoperative triac.
Inoperative controller

Ye s

Defrost operation normal, reprogram button 
one to the time noted above, proceed to 
shutdown condition
(Test Sequence 8).

Test Sequence 8:  Shutdown Condition

60 seconds after a cook cycle or door 
transition, all components shut off?

No

1.
2.

Inoperative controller.
Inoperative holding relay.

3.

Broke or im proper w ire connection.

Yes

Oven operation is norm al.

Summary of Contents for A1200S












































































Reviews:

No comments