Amana A1200S Service Download

Page: 36 / 75

RE220002 Rev. 6`

Troubleshooting Procedures

To avoid risk of electrical shock, personal injury, or death,
disconnect power to unit and discharge the capacitor
before following any disassembly procedures.

WARNING

Diagnosis for VEND-10.H, .J, VEND-10, VEND-11, A1200S, A1225S, FSP-11, FS-11EVP,
FS-16EVP

Test Sequence 9: Idle Condition

Open oven door and connect power cord.

No power applied to the oven power cord.

Blown fuse (Note: Check interlock switch module operation, monitor test).

Colon appears in the display?

Inoperative cavity or magnetron thermal protector.

4.
5.
6.

Inoperative low voltage transformer.
Inoperative controller.
Broken or improper wire connection.

Yes

1.
2.

Inoperative holding relay.
Inoperative controller.

Cavity light is on?

Inoperative low voltage transformer.

Yes

4.
5.

Inoperative cavity light or socket.
Broken or improper wire connection.

Blower motor operates?

Blower motor inoperative or binding.

Broken or improper wire connection.

Yes

Stirrer motor operates?

Inoperative or binding stirrer motor.

Broken or improper wire connection.

Yes

"Idle" operation normal.
Proceed to "Cook" condition
(Test Sequence 10).

Summary of Contents for A1200S












































































Search results

Summary of Contents for A1200S

Reviews:

Related manuals for A1200S

Brands by name

Popular brands

Amana A1200S, Service

Search results

Summary of Contents for A1200S

Reviews:

Related manuals for A1200S

Brands by name

Popular brands