manualshive.com logo in svg

Amana A1200S, Service, Page: 37 / 75

Share
Download
Amana A1200S Service Download Page 37

37

RE220002 Rev. 6

Troubleshooting Procedures

To avoid risk of electrical shock, personal injury, or death,
disconnect power to unit and discharge the capacitor
before following any disassembly procedures.

WARNING

!

Diagnosis for VEND-10.H, .J, VEND-10, VEND-11, FSP-11, FS-11EVP, FS-16EVP

Test Sequence 10:  Cook Condition

Place a cup of water in oven and close oven door.

1. Inoperative controller.

Cavity light is on?

No

2. Broken or improper wire connection.

Yes

1. Button one programmed for zero time.

2. Door not completely latched.

Push button number one, the controller beeps and the display 
starts counting down?

No

3.
4.

Inoperative touch panel.
Inoperative controller.

Yes

5.

       

6.

Inoperative or misadjusted door interlock switch module (Logic 
Test).
Broken or improper wire connection.

Display counts down to zero, and the controller

No

1. Inoperativecontroller.

beeps, and display shows "DONE".

Yes

Heats very slowly

NOTE:  Verify by performing power test

Open oven door.

1. Line voltage less than 110 volts.

2. Inoperative capacitor.

Water placed in the oven is heated?

3. Inoperative magnetron

No

No heat

NOTE:   Due to short time periods programmed into 

NOTE:  Perform isolation test.

the controller, the temperature rise of the water may be slight.

1.
2.

Inoperative controller.
Inoperative power transformer.

Yes

3.
4.
5.
6.

7.
8.

Inoperative diode.
Inoperative capacitor.
Inoperative magnetron.
Inoperative or misadjusted interlock switch module (Primary 
and Secondary Test).
Inoperative triac.
Broken or improper wire connection.

Close oven door and test all timer buttons as follows:  Push 
button number two and observe display countdown.  Interrupt 
countdown by opening and closing door.
Test next button.

1. Zero time programmed for the button.

All button initiate timer countdown?

No

2. Door not completely latched.

3. Inoperative touch panel.

Yes

4. Inoperative controller.

Cook operation normal. 
Proceed to vari-power condition
(Test Sequence 11).

Summary of Contents for A1200S












































































Reviews:

No comments