manualshive.com logo in svg

Amana A1200S, Service, Page: 38 / 75

Share
Download
Amana A1200S Service Download Page 38

RE220002 Rev. 6`

38

Troubleshooting Procedures

To avoid risk of electrical shock, personal injury, or death,
disconnect power to unit and discharge the capacitor
before following any disassembly procedures.

WARNING

!

Diagnosis for VEND-10.H, .J, VEND-10, VEND-11, FSP-11, FS-11EVP, FS-16EVP

Test Sequence 11:  Defrost II Condition

Open oven door, place a cup of cool water in oven, 
close door, push button one and note time in display, 
open door and program button one for one minute of 
defrost, push button one.

Oven starts and times down, cavity light changes 
brillance and the oven sound varies

Oven operates on high only or does not heat at all.

in intensity (pulses) twice approximately every 12 
seconds indicating defrost operation, the water is 
warmed?

 

1.
2.

Inoperative triac.
Inoperative  controller

 

Defrost operation normal, reprogram button one to the 
time noted above, proceed to shutdown condition
(Test Sequence 12).

Test Sequence 12:  Shutdown Condition

60 seconds after a cook cycle or door 
transition, all components shut off?

 

1.
2.

Inoperative controller.
Inoperative  holding relay.

3. Broke or improper wire connection.

 

Oven operation is normal.

Yes

No

Yes

No

Summary of Contents for A1200S












































































Reviews:

No comments